Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateStyles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
See the difference
Before
After
Before
After
Before
AfterHow Much Does Gate Installation Cost in Evergreen?
Gate installation in Evergreen typically runs $2,400-$4,200 for a single-swing driveway gate with an operator, $3,800-$7,500 for a sliding driveway gate, and $450-$1,200 for a pedestrian walkway gate without automation. The price swings mostly on gate width, material, and how much site work the opening needs before anything gets hung. If you already have a gate and it’s misbehaving rather than missing, you likely don’t need this page at all: an existing-system diagnosis is usually the cheaper path, and we’ll tell you honestly when a repair makes more sense than new construction.
We specialize exclusively in gates – repair, electric systems, and installation. That focus is why the numbers below hold up. We aren’t guessing at what a LiftMaster operator adds to a job or what an FAAC setup demands from a property. Whether your system runs LiftMaster, FAAC, BFT, or Mighty Mule, we already know it.
Key Takeaways
- Most Evergreen driveway gate installs land between $2,400 and $7,500 depending on type and automation.
- A walkway gate without an operator is the least expensive option, starting around $450.
- Automation and access control usually account for 40-60% of a full driveway gate cost.
- Site work at the opening – trenching, a new concrete pad, a level grade for a slide gate – is the wildcard that moves the number most.
- Repair-first: if a fix will hold, we’ll say so before we quote a replacement.
Gate Installation Cost Breakdown (2026)
Here’s how the pieces break out in the Evergreen market. These are typical estimated ranges for a standard residential job; the written estimate after we’ve looked at your opening sets the final price.
| Line Item | Typical Estimated Range |
|---|---|
| Pedestrian / walkway gate, manually operated | $450 – $1,200 |
| Single-swing driveway gate, gate only (no operator) | $1,200 – $2,600 |
| Sliding driveway gate, gate only (no operator) | $2,200 – $4,500 |
| Gate operator – residential swing (Mighty Mule, Ghost Controls, Linear) | $600 – $1,400 |
| Gate operator – commercial / estate grade (FAAC, BFT, Viking, LiftMaster) | $1,300 – $3,000 |
| Access control – keypad, entry panel, or intercom (DoorKing, Elite, Linear) | $400 – $1,800 |
| Site work – trenching, concrete pad, grade prep, footing | $500 – $2,500 |
| Safety sensors and safe-closing hardware | $250 – $600 |
Add those together and you can see why a bare swing gate and a fully automated slide gate with keypad access sit so far apart in price. The gate itself is often the smaller half of the bill. The operator, the access control, and the wiring that ties them together are what really move the number, and the site work underneath everything is where surprises live.
Why the operator matters more than the gate
A basic single-swing residential operator from Mighty Mule or Ghost Controls is one of the least expensive ways to automate a driveway gate, and for many Evergreen homes it does the job. On a wider or heavier gate, or at a commercial entrance, that same residential unit will struggle, cycle too often, and wear out early. Stepping up to FAAC, BFT, Viking, or a commercial LiftMaster system costs more up front and can save you a replacement years down the line. Matching the operator to the gate’s actual weight and duty cycle is most of our job on the estimate.
What Affects Gate Installation Pricing in Evergreen
- Gate width and weight. A 12-foot swing gate and a 20-foot slide gate use different frames, hinges, rollers, and operators. Wider and heavier means more steel and a beefier operator, and both costs climb together.
- Material. Steel, aluminum, and composite all price differently, and the material drives how much you spend on the operator too. A light aluminum gate needs less operator than a heavy steel one.
- Automation and access control. Going from a manual gate to a keypad or intercom-controlled entrance is often the biggest single jump in the budget. What you choose – a basic keypad, a multi-unit DoorKing panel, an intercom – sets the ceiling.
- Site conditions at the opening. A level, already-prepped opening keeps site work low. An uneven grade, a need for new concrete footings, or a long wire run from the house to the gate adds labor. The land around an Evergreen property often changes grade quickly over a short distance, so the opening gets measured carefully.
- Power at the gate. If there’s a nearby outlet or a conduit already in the ground, wiring is straightforward. If power has to be run fresh from the house or a panel, that’s added trenching and work.
- Repair vs. new build. If you have an existing gate and operator that’s failing, replacing the operator alone is usually a fraction of a full install. We check first whether the gate, posts, and hardware are still sound before quoting a new install.
If you’re earlier in the process and just wondering whether new construction is even the right move, a quick conversation usually sorts it. The Atlas Gate Repair team can look at what you have before you commit to anything.
How to Save on Gate Installation
There’s real room to trim the budget without cutting corners, and most of it comes from deciding clearly what you actually need.
- Decide manual vs. automated up front. If you can live with a manual gate for now, an operating operator can be added later. It costs less to plan for it than to retrofit it.
- Keep the gate to a sensible size. A gate that fits its opening without extra width or bracing is cheaper in material and cheaper to drive.
- Know your access-control needs. A single homeowner with a keypad doesn’t need a multi-tenant entry panel. Match the control hardware to how many people actually use the gate.
- Do the site work once. If you’re going to trench for power or set a concrete pad, get it right the first time. Redoing site work later is the expensive part.
- Check what’s already there. If an operator or hardware is still good, reuse it. We’ll tell you what can stay.
Estimates are free, and a good estimate should break down the gate, the operator, the access control, and the site work separately so you can see exactly where your money goes. Call (833) 589-9356 to book one.
Repair or Replace? The Question to Answer First
Not every failing gate needs a new install. If you have a gate that stops, reverses, or won’t close, the problem is often in the operator or a sensor, not the gate itself. Replacing an operator on an otherwise sound gate is usually far less expensive than a full build, and we approach every call that way first – we tell you honestly whether a fix or a replacement makes sense. From residential driveways to commercial access control, we cover the full range, so a small repair and a full install get the same careful look.
If your system runs a brand we work with every week – LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, or Mighty Mule – we already know it. That means we can usually tell from a conversation and a look at the gate whether you’re facing a repair bill or an install quote, and that answer shapes everything else.
Permits and What to Check Before You Build
Contact your city’s building department about permits before any gate is installed. Most cities require a permit for a new gate and especially for anything involving new electrical work or a permanent structure at the property line, and some have rules about where a gate and its footing can sit. Ask what applies to your opening before you order a gate. We’ll point out what to ask, and the written estimate will reflect what your specific site needs. On any job with power wiring or a heavy gate panel, we also recommend a trained professional – a miswired operator is a shock hazard, and an improperly hung slide gate can come off its track.
If you’d like an idea of what neighborhoods we cover and how locals typically set up their properties, the Evergreen page is a good place to start.
Same-Day Repair and What Happens When You Call
If your gate is already in and something’s broken, you don’t have to wait for an install. Call (833) 589-9356. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday. We’re closed Saturday. A call outside dispatch hours is booked into the next opening, Sunday through Friday, 7am to 7pm.
Same-day service is available for many repairs, and a diagnosis is the fastest way to find out whether you’re looking at a repair or a replacement. Diagnosed fast. Fixed right. No guesswork.
Why Choose a Gate Specialist for Your Installation
We do gates – repair, electric systems, and installation – and nothing else. That single focus means the technician at your Evergreen property knows operators and access control, not just general handyman work. Fluency across nine major gate brands means they aren’t learning on your gate, and they aren’t guessing at your operator.
We cover both ends of the market: entry-level residential brands like Mighty Mule and Ghost Controls, and commercial or estate-grade systems like FAAC, BFT, Viking, and DoorKing. No job is too simple or too complex for that range. From a small walkway gate to a commercial access-control entrance, we’ve worked with the hardware.
Atlas Gate Repair has been serving Evergreen since 2017. In that time the company has built its name on honest assessments – repair-first, replacement only when the gate and operator are truly at the end of their life.
FAQs – Gate Installation Cost
How much does a basic driveway gate cost to install in Evergreen?
A basic single-swing driveway gate with a residential operator typically runs $2,400-$4,200 in Evergreen, including the gate, the operator, and the wiring. Without automation, the gate-only range is closer to $1,200-$2,600. Call (833) 589-9356 for an exact quote – estimates are free.
Is it cheaper to repair or replace a gate?
Repairing an existing gate is almost always cheaper than a full install when the gate frame and posts are sound – usually a fraction of the cost. Replacing the operator alone is a common fix, and we check first whether a repair will hold before quoting a new gate. Call (833) 589-9356 and we’ll tell you which path makes sense.
What’s the most expensive part of a gate installation?
Automation and access control are usually the biggest line items, often 40-60% of a full driveway gate cost. A commercial-grade operator and multi-unit entry panel can cost more than the gate itself. Call (833) 589-9356 for a breakdown specific to your gate and entrance.
Do you need a permit to install a gate in Evergreen?
Most cities require a permit for a new gate, especially with electrical work, so ask your city’s building department what applies at your opening. We’ll flag what to ask and build the cost into your written estimate. Call (833) 589-9356 to get started.
Can you install a gate on an uneven grade?
Yes, uneven grade is common around Evergreen properties and usually handled with proper footings and site prep, which typically adds $500-$2,500 to site work. A site visit is the most accurate way to price it. Call (833) 589-9356 to book a free estimate.
Getting a Real Number for Your Property
The ranges above are a starting point, not a promise. Every gate opening is a little different, and the written estimate is what sets the final price. Call (833) 589-9356 for a free estimate. We answer 24/7, with fast dispatch from 7am to 7pm, Sunday through Friday, closed Saturday. Whether you’re weighing a repair against a new install, or you’re ready to build, we’ll give you a straight answer and a clear breakdown of what the job involves.
Pricing reflects the Evergreen market as of 2026. Atlas Gate Repair offers free estimates – call (833) 589-9356.
Written by the team at Atlas Gate Repair, serving Evergreen since 2017.
What Our Customers Say
"Control board fried after a lightning storm. He showed me the burn mark on it, quoted the board, and installed a surge protector on the line so it hopefully doesn't happen again."
- Whitney Fletcher"Gate stopped halfway and sat there for two days blocking the driveway. He found a dead capacitor in the operator, had one with him, and we were moving cars again in under an hour."
- Bethany Ackerman"Reprogrammed every clicker in the HOA and set up the keypad codes. Patient with a very long list of residents."
- Matt Reed