Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateStyles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
See the difference
Before
After
Before
After
Before
AfterHow Much Does Gate Motor & Opener Cost in Evergreen?
A gate motor or opener replacement in Evergreen typically runs $650 to $2,400 for the unit and installation, depending on the brand and whether the gate is a residential swing system or a commercial slide gate. Most residential driveway swaps land between $650 and $1,200, while heavy-duty commercial operators and access-control systems push higher. The written estimate sets the final price, and it’s free.
We’re Atlas Gate Repair, and gates are the only thing we do. Motor and opener pricing gets quoted badly all the time because the unit isn’t the whole story: arm geometry, power runs, safety sensors and access control all move the number. Below is what we actually see in the Evergreen market for 2026.
Key Takeaways
- Typical residential motor and opener replacement in Evergreen: $650-$1,200.
- Commercial and estate-grade operators (FAAC, BFT, DoorKing): $1,200-$2,400, sometimes more.
- If the arm, board or sensors are the only failure, a repair under $400 is often possible.
- We work across nine brands, including LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite and Mighty Mule.
Gate Motor & Opener Cost Breakdown (2026)
Here’s how the numbers break out for the Evergreen market. These are typical estimated ranges, not a menu; every gate gets priced on its own written estimate.
| Line item | Typical estimated range |
|---|---|
| Residential swing gate operator (Mighty Mule, Ghost Controls, Elite) | $650 – $1,200 installed |
| Residential slide gate operator (Linear, LiftMaster) | $900 – $1,500 installed |
| Commercial / estate operator (FAAC, BFT, Viking, DoorKing) | $1,200 – $2,400 installed |
| Control board or logic board replacement | $250 – $600 |
| Motor or gearbox replacement (operator stays in place) | $350 – $800 |
| Safety sensor pair (photo-eye or loop) | $200 – $450 |
| Keypad or access-control interface | $250 – $700 |
| Battery backup for the operator | $200 – $450 |
| New dedicated power run to the gate | $400 – $1,200 |
What pushes a quote up: commercial-grade equipment, a gate that’s heavy or long, an old installation with tired wiring, and access control that has to talk to a building or HOA system. What pulls it down: a unit that’s still healthy and only needs a board, arm or sensor. That’s the repair-first call we make on every job. If a $300 board brings the operator back, we tell you that before we quote a replacement.
What Affects Gate Motor & Opener Pricing in Evergreen
- Brand and grade. A Mighty Mule or Ghost Controls residential operator sits at the low end. FAAC, BFT, Viking and DoorKing systems sit at the top, because they’re built for duty cycles a driveway never sees. We know all of these by sight, so we’re not guessing which tier your gate needs.
- Gate weight and travel. A short single swing is a straightforward swap. A long slide gate or a double swing pair needs a bigger operator, and often two. That’s real cost, not markup.
- Access control. Keypads, intercoms, telephone entry and card readers add hardware and wiring. On HOA and commercial properties this is often the part that surprises a budget.
- Power at the gate. If there’s a live circuit near the operator, installation is simpler. If not, a new dedicated run adds cost. Solar options exist for some residential units but not every brand supports them.
- Age of the installation. Old wiring, corroded terminals and a tired control box turn a simple motor swap into a bigger job. We inspect before we quote, so the number holds.
- Safety hardware. Photo-eyes, loops and reversing sensors aren’t optional on an automated gate. They’re part of the operator cost, and skipping them isn’t something we’ll do.
How to Save on Gate Motor & Opener
The biggest savings come from not replacing what still works. A board, a gearbox or a set of sensors is a fraction of a full operator, and a technician who knows the brand can usually tell the difference in one visit.
- Get the diagnosis first. A written estimate that names the failed part is worth more than a low number with no detail.
- Keep the operator clean and the gate tracking straight. A gate that drags wears out a motor fast.
- Don’t skip safety sensors to save a few hundred dollars. It’s the wrong place to trim.
- Match the operator to the gate. Oversizing wastes money; undersizing burns out the unit early.
- If the gate itself is failing, a repair is often cheaper than a new motor. Our gate repair work and operator work go hand in hand, and we quote both honestly.
Estimates are free. Call (833) 589-9356. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
FAQs – Gate Motor & Opener Cost
How much does a gate motor cost in Evergreen?
Expect $650 to $2,400 installed, with most residential driveway operators between $650 and $1,200 and commercial or estate systems above that. Call (833) 589-9356 for a free written estimate on your exact gate.
Is it cheaper to repair or replace a gate opener?
Repair is usually cheaper when the failure is a board, arm, sensor or gearbox, often $250 to $800, versus $650 and up for a full unit. We quote the repair first and only recommend replacement when the operator is truly worn out. Call (833) 589-9356 and we’ll tell you which one your gate needs.
Do you work on my brand of operator?
We work across nine brands, including LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite and Mighty Mule. That covers the residential staples and the commercial-grade systems under one roof. Call (833) 589-9356 and tell us what’s on your gate.
Can you come today?
Same-day visits are often possible. We answer 24/7 and dispatch Sunday through Friday, 7am to 7pm. Call (833) 589-9356 and we’ll book the soonest opening for your gate.
Why is my commercial operator quote higher than a residential one?
Commercial operators carry higher duty ratings, heavier hardware and access-control integration, which is why they land at $1,200 to $2,400 instead of $650 to $1,200. The unit and its control system are built for constant use. Call (833) 589-9356 for an estimate that fits your property.
Get a Free Gate Motor & Opener Estimate in Evergreen
We do gates and nothing else, so the technician who arrives already knows your operator. Whether it runs LiftMaster, FAAC, BFT or Mighty Mule, we diagnose it fast and fix it right. Atlas Gate Repair has been working on automated and access-control gates since 2017, and we cover both residential driveways and commercial properties across the area.
Call (833) 589-9356 for a free estimate. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday. A call outside dispatch hours is booked into the next opening. The written estimate sets the final price, and there’s no charge for it.
Pricing reflects the Evergreen market as of 2026. Atlas Gate Repair offers free estimates – call (833) 589-9356.
What Our Customers Say
"Our slide gate had been dragging for months and getting worse. Turned out the chain was stretched and one of the guide rollers had seized. Both replaced, and he adjusted the limits so it stops properly at both ends now."
- Adriana Castillo"Fixed the immediate problem. He was honest that the operator is near end of life and I should budget for a replacement, which I appreciate even if it wasn't what I wanted to hear."
- Henry Chen"Control board fried after a lightning storm. He showed me the burn mark on it, quoted the board, and installed a surge protector on the line so it hopefully doesn't happen again."
- Whitney Fletcher