Gate Repair in Evergreen - On-Site in 60 Minutes, Fixed the Same Day

Trusted Gate Repair for Evergreen Homeowners

Gate repair in Evergreen typically runs $180 to $480 for most mechanical and electrical fixes, and we can usually have a technician at your property the same day you call. A gate that won’t open, sags on its hinges, or grinds against the track is more than a nuisance. It’s a security gap on your property. Our team at Atlas Gate Repair specializes in gates exclusively, so we diagnose the actual problem instead of guessing at it. We answer 24/7 and dispatch technicians from 7am to 7pm, Sunday through Friday. Call (833) 589-9356 for a free estimate, and we’ll give you a written price before any work begins.

Call (833) 589-9356

Driveway Gate Repair

Driveway Gate Repair means restoring an automatic or manual gate to safe, reliable function. You need it when your gate won’t open or close, moves unevenly, makes grinding noises, or sags so badly it scrapes the driveway. We trace the problem to its source, whether that’s a worn roller, a failing operator board, a bent hinge, or a misaligned track. Most driveway gate repairs in Evergreen run $180 to $380 depending on what’s failed and how long it takes to reach. We carry diagnostic equipment for LiftMaster, FAAC, BFT, and Linear systems, so we’re not standing in your driveway reading a manual on our phone. Your written estimate sets the final price, and we agree on it before we start.

Operators and Remote Systems

When a gate moves but won’t complete its cycle, the operator is usually the first place we look. A LiftMaster or Linear board can fail slowly, causing intermittent behavior that’s easy to misdiagnose. We test the control board, limit switches, and safety sensors. We won’t tell you to replace a motor when a $30 limit switch is the real fault.

Hinges, Posts, and Alignment

A heavy driveway gate eventually shifts its posts, especially in Evergreen’s clay-heavy soil. That shift throws the gate out of square and puts stress on the hinges. We re-level and reinforce what’s needed, and weld or rebolt hinges when they’ve pulled loose. The goal is a gate that swings or slides the way it did when it was installed.

Gate Welding

Gate Welding is what we do when a metal gate cracks, a hinge tears off, or a post anchor fails. Cast-iron and steel gates don’t usually bend, they crack and then they get worse fast. A weld done properly holds for years; a bad one fails in months, often at the worst time. In Evergreen, gate welding work typically costs $75 to $120 per repair point, with full hinge replacement and reinforcement running higher. Our welders work on ornamental steel, aluminum, and wrought iron. We don’t paint over a crack and call it fixed. The written estimate reflects what we actually see through our inspection, not a guess over the phone.

Structural Repairs and Reinforcements

When the bottom rail of an iron gate rusts through, the whole gate loses its structure. We cut out the compromised section and weld in a solid replacement, then reprime and coat it to match your gate. We check the surrounding joints too, because a crack in one corner usually means stress is traveling through the frame.

Post Anchors and Gate Frames

A weld only holds if the metal around it is sound. If the post anchor is pitted or deeply rusted, we reinforce or replace the plate before we weld the gate back onto it. We use fabrication techniques that suit the existing metal, never forcing modern steel into an old iron frame without proper prep. A proper bond at the base is what keeps a gate square for years.

Commercial Gate Repair

Commercial Gate Repair covers sliding access gates, barrier arms, and heavy-duty automated systems for HOAs, apartment buildings, and commercial properties. These gates cycle dozens or hundreds of times a day, so parts wear faster than residential hardware. We service the full range of operators, including FAAC, BFT, Viking, and DoorKing, and we know their common failure points cold. Commercial repair may start around $280 and run higher depending on the operator and access control work involved. We respond to Evergreen commercial properties with quick dispatch from 7am to 7pm, Sunday through Friday. The estimate is free, and we quote the written price before touching the gate.

High-Cycle Systems

A commercial gate that cycles every 90 seconds all day is a completely different animal from a driveway gate that opens four times daily. We check the drive chain, belt, roller trucks, and motor temperature. Heat buildup and worn rollers tell us more than any symptom alone. We replace parts before they cascade into a failure that blocks resident access.

Access Control Integration

When a card reader, keypad, or intercom stops triggering the gate, the problem could be the operator, the wiring, or the access control panel itself. We test the circuit end to end, from the keypad to the operator motor. We work on existing systems without pushing you into a full access control replacement unless that’s genuinely the right call. Our repair-first approach keeps your gate operational while you decide on bigger changes.

Iron Gate Repair

Iron Gate Repair deals with solid or ornate metal gates, which are common across Evergreen’s established neighborhoods. The primary problems are rust, cracked welds, sagging, and seized hinges. We grind back rust, weld cracks closed, reinforce thin sections, and rebalance the gate on its hinges. Typical iron gate repair work in Evergreen falls between $200 and $450, though a badly rusted frame needing sectional replacement will run higher. We don’t hide patches behind paint. Every repair gets primed and coated to match, and we tell you honestly whether a frame is too far gone for a sound repair. Written estimate first, agreed price before any work.

Rust Treatment and Frame Integrity

Rust is the slow killer of iron gates. Surface rust we can clean and coat. Deep pitting or holes mean that section has lost its strength. We inspect every structural member, not just the visible face. If the frame is sound, we restore it. If it’s too far gone, we’ll tell you that instead of selling a repair that won’t last.

Hinge Pins and Pivot Points

Iron gates often fail at the hinge pin first. The weight of the gate grinds the pin into the socket, and eventually it seizes or drops. We align the gate, replace pins and bushings where needed, and make sure both hinges carry the load evenly. Fixing this early stops the gate from sagging and pulling the post out of plumb.

Sliding Gate Repair

Sliding Gate Repair addresses gates that roll along a track rather than swinging on hinges. You know you need it when the gate jumps the track, scrapes the ground, stops midway, or the motor strains. This style is popular in Evergreen for long driveways and commercial entries where a swing gate would need too much room. Most sliding gate repairs run $220 to $480 depending on whether we’re replacing rollers, repairing the chain, or rewiring the motor. We check the track alignment, roller wear, rack, limit switches, and operator drive. Then we explain what failed and what it costs to fix before we start. A sliding gate that works smoothly should glide, not grind.

Rollers, Track, and Cantilever Hardware

Track style and cantilever gates both depend on rollers carrying the full weight of the panel. Worn rollers make the gate wobble and eventually jump. We replace roller assemblies as a set, not one at a time, so the gate doesn’t come back out of alignment in a month. We also inspect the track base and guide posts for concrete cracking that can develop in heavy soil over time.

Chain, Belt, and Motor Drives

The drive system is where sliding gates show their problems first. A stretched chain slips. A worn belt makes the motion jerky. A motor that hums but doesn’t move the gate can be a bad capacitor or a seized gearbox. We identify which part failed and replace that part, not the whole operator, unless the operator is genuinely finished. That’s the difference between a repair and a wholesale replacement you didn’t need.

Wrought Iron Gate Repair

Wrought Iron Gate Repair covers decorative gates with the distinctive hand-forged look many Evergreen homes have. These gates are visually beautiful and structurally particular. The scrolling and curves hide stress points where older welds crack. Common jobs include straightening bent pickets, repairing broken scrollwork, rebuilding hinge mounts, and treating rust. Expect to pay $250 to $500 in Evergreen for wrought iron gate repair, depending on the amount of fabrication and finishing work involved. We match the repair to the original design, and we take care not to scorch or warp the surrounding metal. The estimate is written and the price is set before we begin.

Ornamental Detail Matching

Wrought iron is not all the same. Older gates often have a mix of forged and cast elements, and matching that profile takes a practiced eye. Where a scroll or finial is broken beyond repair, we fabricate a replacement that matches the pattern. The goal is that you cannot tell it was repaired unless someone points it out.

Finish Preparation and Sealing

A fresh weld on a wrought iron gate is bare metal. If we don’t prep and seal it correctly, it becomes a new place for rust to start. We wire-brush the affected area, apply a rust-inhibiting primer, and finish with a topcoat matched to the gate. That finish is part of the repair, not an add-on we quote after the fact.

Metal Gate Repair

Metal Gate Repair is the broad category covering steel, aluminum, and tubular gate frames. You need it when the gate sags, a weld breaks, a hinge tears loose, or the frame twists. Aluminum gates are lighter and often easier to work with, but they crack differently than steel. Steel gates are heavier and more forgiving to heat, but they rust if the finish fails. Evergreen metal gate repair usually falls between $180 and $400 depending on the metal type and the extent of the damage. We identify what metal you have and match our repair approach to it. No guessing, no generic hardware, and no price surprises. The written estimate tells you everything before we start.

Steel vs. Aluminum Repairs

Steel responds well to welding and reinforcement. Aluminum can be welded too, but it requires different filler and more heat control to avoid distortion. Using the wrong process on an aluminum gate is how you end up with a buckling panel or a brittle repair. We choose the right method for your gate’s metal, and we explain why it matters.

Frame Straightening and Squaring

A metal gate that drags on one corner is either sagging or the frame has twisted. We measure the frame diagonally to find where it’s out of square, then straighten or reinforce accordingly. On tubular gates, this often means welding in an internal brace. The result is a gate that closes evenly and latches without a fight.

Wood Gate Repair

Wood Gate Repair deals with driveway and pedestrian gates built from wood. In Evergreen’s mild climate, wood gates rarely rot from freeze-thaw, but they do dry out, crack, and pull away from their hardware. The big problems are split rails, loose or stripped hinge screws, warped panels, and sagging that drags the latch out of alignment. Wood gate repair typically runs $160 to $320 in Evergreen. We replace rotted or split sections, re-bore stripped hinge holes with proper dowels, and get the gate back to square. We don’t paint or stain over a problem that needs structural fixing. You approve the written estimate before we do any work.

Rail and Panel Replacement

The bottom rail of a wood gate takes the most weather and weight. When it splits, the whole gate loses its shape. We cut and fit replacement rails that match the existing wood species and profile. The repair is structural, not cosmetic, and we seal the joint so moisture does not sit in it.

Hinge Reinforcement and Latch Alignment

Wood gates sag because hinge screws strip out of the wood or the post shifts. We remove the old screws, fill the holes with hardwood dowels and adhesive, then re-set the hinges. Once the gate hangs plumb, we align the latch and striker. This saves you from having to lift the gate while you turn the key.

Brands We Service

We service LiftMaster gate operators and know the control boards, limit switches, and motor capacitors that fail most often on their residential and light commercial units. If your LiftMaster remote works intermittently or the gate reverses for no reason, we can pinpoint the fault on the first visit instead of swapping parts until it works. We also service FAAC equipment, a brand common on European-style swing gates and estate properties. FAAC operators have distinct hydraulic and electromechanical models, and the troubleshooting paths are different for each.

BFT systems are another brand we see frequently on larger residential and multi-unit properties in the Evergreen area. We know how BFT’s control boards respond to sensor faults and how to reset programming without wiping your remotes. Linear gate operators show up on a lot of newer installations, and we’re familiar with their wiring patterns and common failure points. We work with all nine major brands we support, but we never claim to be factory-certified by any of them. We are independent, experienced, and familiar with the equipment. Whether you have a LiftMaster, FAAC, BFT, Linear, or any other make of gate, we can diagnose the problem and give you an honest answer on repair versus replacement.

Signs You Need a Pro Right Now

• Your gate groans or grinds while moving. That sound usually means a roller is seizing, a hinge is dry and worn, or the operator’s gearbox is struggling. Left alone, the part fails completely and the gate stops moving entirely, usually when a car is in the wrong place at the wrong time.
• The gate jerks or starts and stops mid-cycle. Jerky motion points to a failing capacitor, a stretched chain, or a bad limit switch. These problems don’t smooth out on their own. They get worse because the system keeps trying to work around the fault, which strains everything else.
• The gate sags and scrapes the ground or the latch misses the post. Sagging means the hinges or frame have lost their integrity. Every open and close cycle makes it worse, and you’re slowly bending the frame. Eventually even a good weld won’t bring it back square without a lot more work.
• The opener runs but the gate doesn’t move. This can be a sheared key, a broken chain, or a failed gearbox. Running the motor while the gate is stuck overheats the operator and turns a simple mechanical fix into an electrical one. Stop using it and call us.
• The remote or keypad works sometimes, not every time. Intermittent operation is frequently a receiver board issue, wiring that’s losing connection, or a failing transformer. It won’t fix itself, and it tends to become permanent at the least convenient moment.

Our Process, Step by Step

1. 1
   You call and describe the problem. Tell us what the gate is doing and what it’s not doing. We answer 24/7. If it’s outside dispatch hours, we book you into the next available opening, Sunday through Friday, 7am to 7pm. There’s no charge for the phone consultation or the on-site estimate.
2. 2
   A technician arrives and inspects the gate. We test the mechanical components, the operator, and the wiring. We look at how the gate sits in its frame, how the rollers or hinges are wearing, and what the motor sounds like under load. Expect this inspection to take from 30 to 60 minutes on most residential gates.
3. 3
   You get a written estimate. We tell you what’s wrong, what needs to happen, and exactly what it costs. If a repair makes sense and a replacement doesn’t, we say so. If a replacement is the honest answer, we’ll explain why. You approve the number before any work starts.
4. 4
   We complete the repair or replacement. Most gate repairs finish the same day, especially common fixes like hinge replacement, roller swaps, capacitor changes, and limit switch adjustments. More involved welding or structural work may need a return visit, and we’ll tell you that upfront and schedule it plainly.
5. 5
   We test the gate through full cycles. We run the gate open and closed multiple times under remote, keypad, and manual operation where applicable. We check the safety sensors and auto-reverse functions. You watch it work before we leave. The price you approved is the price you pay.

How Much Does Gate Repair Cost in Evergreen?

Our Service Area Near Evergreen

We work throughout Evergreen and the neighboring communities. Our technicians regularly handle gate repair in East San Jose and gate repair in Silver Creek Country Club. We also cover Willow Glen, Cupertino, Central San Jose, Spartan Keyes, Downtown San Jose, Berryessa, South San Jose, and Los Alamitos Creek. Some of our Evergreen customers are close enough that we can be on-site within the hour. Other areas nearby may take a little longer depending on traffic across the valley. Call us with your address and we’ll give you a straight answer on when we can get there.

Frequently Asked Questions About Gate Repair in Evergreen

Schedule Your Gate Repair Service in Evergreen Today

Your gate is a working part of your home or property, and when it fails, it needs a specialist, not a handyman with a multitool. Call (833) 589-9356 to schedule your free estimate. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday. We’ll diagnose the problem, give you a written price, and get your gate working right.

Written by Gus Walsh, Owner at Atlas Gate Repair, serving Evergreen since 2017.